Digiplex EVO641R Instalační manuál Strana 53
- Strana / 68
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
Digiplex -EVO- - 53 - Programming Guide
Contact ID Report Code List
If using the Ademco Contact ID format, key in the 2-digit hexadecimal value (PROG. VALUE) to program the desired report codes into sections [0201] to
[0296], [0701] to [0832], [2001] to [2199], and [3900] to [3999].
Module TLM restore 3 352 - Telco 2 fault restore LR - Phone Line Restoral
Early to Arm by User 3 451 - Early to Close CK - Early to Close
Late to Arm by User 3 452 - Late to Close CJ - Late to Close
Zone Excluded on Force Arming 1 57A - Zone Bypass XW - Zone Forced
Zone Went Back to Arm Status 3 57A - Zone Bypass Restore VV - Zone Included
Printer fault restore 3 336 - Local printer failure restore VR - Printer Restore
Module AC restore 3 3A1 - AC loss restore AR - AC Restoral
Module battery restore 3 3A9 - Battery test failure restore YR - System Battery Restoral
Module Auxiliary supply restore 3 3AA - System trouble restore YQ - Power Supply Restored
Fail to communicate with monitoring station 1 354 - Fail to communicate YC - Communication Fails
Module RF low battery 1 384 - RF transmitter low battery XT - Transmitter Battery Trouble
Module RF supervision trouble 1 381 - Loss of supervision - RF US - Untype Zone Supervision
Module RF battery restore 3 384 - RF transmitter battery restore XR - Transmitter Battery Restoral
Module RF supervision restore 3 381 - Supervision restore - RF UR - Untyped Zone Restoral
Cold Start 1 3A8 - System shutdown RR - Power Up
Warm Start 1 3A5 - System reset YW - Watchdog Reset
Test Report engaged 1 6A2 - Periodic test report TX - Test Report
Listen-In request 1 606 - Listen-In to follow LF - Listen-In to follow
WinLoad Login request 1 411 - Call Back Request RB - Remote Program Begin
PC software communication finished 1 412 - Successful - download access RS - Remote Program Success
Installer on site 1 627 - Program mode Entry LB - Local Program
Installer programming finished 1 628 - Program mode Exit LS - Local Program Success
Module Fail to Communicate Restore 3 354 - Fail to Communicate Restore YK - Communication Restore
CID# Reporting Code
Prog.
Value
CID# Reporting Code
Prog.
Value
CID# Reporting Code
Prog.
Value
MEDICAL ALARMS - 100 BURGLAR ALARMS - 130 150 24-Hour Non-Burglary 25
100 Medical Alarm 01 130 Burglary 13 151 Gas Detected 26
101 Personal Emergency 02 131 Perimeter 14 152 Refrigeration 27
102 Fail to Report In 03 132 Interior 15 153 Loss of Heat 28
FIRE ALARMS - 110 133 24-Hour 16 154 Water Leakage 29
110 Fire Alarm 04 134 Entry/Exit 17 155 Foil Break 2A
111 Smoke 05 135 Day/Night 18 156 Day Trouble 2B
112 Combustion 06 136 Outdoor 19 157 Low Bottled Gas Level 2C
113 Water Flow 07 137 Tamper 1A 158 High Temperature 2D
114 Heat 08 138 Near Alarm 1B 159 Low Temperature 2E
115 Pull Station 09 139 Intrusion Verifier 1C 161 Loss of Air Flow 2F
116 Duct 0A GENERAL ALARMS - 140 162 Carbon Monoxide Detected 30
117 Flame 0B 140 General Alarm 1D 163 Tank Level 31
118 Near Alarm 0C 141 Polling Loop Open 1E FIRE SUPERVISORY - 200 & 210
PANIC ALARMS - 120 142 Polling Loop Short 1F 200 Fire Supervisory 32
120 Panic Alarm 0D 143 Expansion Module Failure 20 201 Low Water Pressure 33
121 Duress 0E 144 Sensor Tamper 21 202 Low CO2 34
122 Silent 0F 145 Expansion Module Tamper 22 203 Gate Valve Sensor 35
123 Audible 10 146 Silent Burglary 23 204 Low Water Level 36
124 Duress-Access Granted 11 147 Sensor Supervision Failure 24 205 Pump Activated 37
125 Duress-Egress Granted 12 24-HOUR NON-BURGLARY - 150 & 160 206 Pump Failure 38
System Event
Default Contact ID Report Code
when using sections [4032] to [4037]
Default SIA Report Code
when using sections [4032] to [4037]
- Hardware Requirements 2
- Hardware Differences 2
- Table of Contents 3
- Things You Should Know 3
- Entering Programming Mode 3
- Serial Number List 4
- Zone Programming 9
- Zone Information 10
- Zone report codes 15
- Zone Labels 17
- Keyswitch Programming 19
- Programmable Outputs 21
- †: See page 27 25
- † 001 to 064 001 to 064 25
- † Not Used Not Used 25
- Input Speeds 28
- Installer Code Programming 28
- User Code Options 29
- Arming Report Codes 30
- Disarming Report Codes 30
- Access Control Sections 31
- Schedule Programming 32
- SECONDARY SCHEDULES 33
- Backup Schedules 34
- Programming Access Levels 34
- Holiday Programming 34
- Keypad Numbering 35
- Remote Control Programming 35
- Control Panel Settings 36
- System Options 36
- Dialer Options 38
- Other Options 38
- Communication Settings 39
- Reporting Formats 40
- VDMP3 Voice Module 41
- Partition Settings 42
- Partition Timers 43
- Partition Options 1 43
- Partition Panic Alarm Options 45
- Partition Bell Squawk Options 45
- Partition One-Touch Options 45
- Partition Special Options 46
- Special Arming Exit Delay 47
- No Movement Schedule 47
- Other Settings and Modes 49
- Software Reset 50
- Installer Function Keys 51
- Automatic Report Code List 51
- System Event 52
- Default SIA Report Code 52
- Contact ID Report Code List 53
- VDMP3 Installation Diagram 55
- Feature Activation (PGMs) 55
- N 12Hr clock 56
- N Disabled 56
- [018]: Beeping Assignment* 57
- Message Programming 58
- Using the Memory Key 59
- Memory Key (PMC-5) 59
- Combus Voltmeter 59
- BLK and Z1 terminals 60
- BLK and Z2 terminals 60
- Single Zone Inputs 61
- ATZ - Double Zone Inputs 61
- Connections 62
- Telephone Line Connections 63
- Built-in RTC 64
- PCB Layout 65
- Warranty 67
- Limitations of Alarm Systems 67
- Trouble Display 68
Související produkty a manuály pro Bezpečnostní systémy pro řízení přístupu Digiplex EVO641R
(32 stránky)© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.306 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce